Digital Home Creations

Digital Home Creations

Furman® ASD-120 2.0 Sequencing Power Distrubution

Model #: ASD-120 2.0

$1,994.95

At a Glance

Updated for easier installation and operation, the ASD-120 2.0 is a compact rack-mount power distribution system for use where AC power must be distributed to multiple circuits and there is no hard-wired, built-in system.

WarningProposition 65 Warning for California Residents
Furman® ASD-120 2.0 Sequencing Power Distrubution

Proposition 65 Warning

WarningWARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov

General

FamilyContractor Series
Line Voltage120 (Volts)
Dimensions3.5" H x 19" W x 10" D (8.9 x 48.3 x 25.4 cm)Â
Weight16 lbs

Shipping Info

Length21.8 (Inches)
Width19.3 (Inches)
Height8.6 (Inches)
Weight19.95 (Lbs)
Unit of MeasureEach
Master Pack Qty2

General Specs

Depth (in.)10
Width (in.)19
Height (in.)3.5
Number Of Outlets12
Shipping Depth (in.)21.8
Shipping Width (in.)19.3
Shipping Height (in.)8.6
Manufacturer Warranty3 Year
Product Weight (lbs.)16

Furman® ASD-120 2.0 Sequencing Power Distrubution

Model #: ASD-120 2.0
184057
Model #: ASD-120 2.0
Furman
$1,994.95

Visit Store For Details

$1,994.95

At a Glance

Updated for easier installation and operation, the ASD-120 2.0 is a compact rack-mount power distribution system for use where AC power must be distributed to multiple circuits and there is no hard-wired, built-in system.

Get to know this product.

The ASD-120 2.0 AC Sequenced Power Distributor updates the ASD-120, optimized for easier installation and operation. The ASD-120 2.0 is an extremely compact, low cost rackmount power distribution system ideal for touring PA systems, touring musical and theatrical acts, mobile recording facilities, on-location film and video shoots, etc. - any situation where AC power must be distributed to multiple circuits and a hard-wired, built-in system is missing, inadequate or impractical.

The ASD-120 2.0 allows you to power up and its six circuits in a sequenced fashion. The sequence is reversed for power down. The delay interval is user-adjustable via an internal trimpot.

Power sequencing is needed whenever various kinds of equipment must be powered up or down in groups, rather than all simultaneously. In audio systems, sequenced powering is often necessary to allow turn-on transients from low level amplifiers and processors to settle down before any power amps are turned on, because simultaneous powering would result in a loud, annoying, and potentially destructive 'pop' reaching the speakers. And in any large system whose components present an inductive load to the AC line (including electric motors, power supplies, and power amplifiers of all kinds), sequenced powering can avoid excessive inrush currents that cause circuit breakers to trip even though the steady-state currents are not excessive.

The ASD-120 2.0's front panel provides a three-position switch for each circuit that allows each circuit to be part of the power up/down sequence, or to remain on or off apart from the sequence. An LED that indicates when either the power-up or power-down sequence is in progress. The sequence can be initiated with either momentary or maintained switches, locally or remotely. A duplex outlet is provided for each delay step. A locking switch with a removable key is provided for maximum security.

Since the sequence control signals are also available on the rear panel, one or more ASD-120 2.0s may be installed in remote locations and operated via low-voltage control wiring. The sequence control signals can also drive PowerPorts, MiniPorts, PS-PRO and PS-8-R Power Sequencers, or any other circuits that need to know when their particular time delay has elapsed. Using one or more ASD-120's can provide the capability of controlling power and power sequencing for an entire system.

The ASD-120 2.0 can handle up to 120 amps of incoming power, distributing it to six 20 amp, 120V circuits. Each circuit has a front panel status indicator that lights up when it is turned on, and a 20 amp duplex outlet on the rear panel.

The ASD-120 2.0's design incorporates four oversized busses, allowing wiring for 120V or 240V single phase, or 208V three phase power. A strain relief clamp is provided that can accommodate a cable or wire bundle up to 1.5 inches in diameter. Cable termination is a simple process of breaking out and stripping the individual conductors and connecting them with set screws, and then tightening the strain relief clamp. Complete instructions accompanying the unit guide the user through the process of selecting and terminating the supply cable.

120 amp total load

Six 20 amp, 120 volt circuits, each with a status indicator

Oversized buss bars

Four buss design accommodates 120V or 240V single phase, or 208V three phase power

Six widely spaced duplex outlets on rear panel

Outlets can be powered up and down in sequence

Three position switch allows each circuit to be part of the power sequencing, or to be switched on/off independently

Sequence timing can be initiated from unit or remotely, using low voltage control wires

Sequence control signals are available on rear panel to drive additional ASD-120 2.0s or other devices and circuits

Front panel key switch for security

Compact two rack space package

Most economical product of its type

Specifications

General Specs

Depth (in.)10
Width (in.)19
Height (in.)3.5
Number Of Outlets12
Shipping Depth (in.)21.8
Shipping Width (in.)19.3
Shipping Height (in.)8.6
Manufacturer Warranty3 Year
Product Weight (lbs.)16

General

FamilyContractor Series
Line Voltage120 (Volts)
Dimensions3.5" H x 19" W x 10" D (8.9 x 48.3 x 25.4 cm)Â
Weight16 lbs

Shipping Info

Length21.8 (Inches)
Width19.3 (Inches)
Height8.6 (Inches)
Weight19.95 (Lbs)
Unit of MeasureEach
Master Pack Qty2

Proposition 65 Warning

Warning:WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
WarningProposition 65 Warning for California Residents